What are the communication settings to control IFP via RS232 and LAN commands?

RS232 Communication Setting  - Baud Rate Select: 9600bps (fixed) - Data bits: 8 bits (fixed) - Parity: None (fixed) - Stop Bits: 1(fixed)   LAN Communication Setting - Type: Ethernet  - Protocol: TCP/IP - Port: 5000 (fixed) - Cross subnet: No - Logon Credentials: No

How to customize an Android Boot Animation on CDExx10 series and CDM models?

1. Overview The "Android Boot Animation" is a script used to load PNG files when the device boots. It is contained within an uncompressed zip file called bootanimation.zip. 2. Inside the bootanimation.zip file The bootanimation.zip file contains: The image folder(s) (containing PNG images named by incremental numbers) The desc...

How to disable the internal speaker and output volume from the line out for CDE5510, CDE6510, CDE5010?

You can set the volume to 0 (to disable internal speaker volume) and set the Audio out (Line out) volume.       The volume of the Audio out (Line out) is suggested to control by an external sound bar for higher output.  

What network port shall be opened for Signage Manager and media player such as NMP-302W?

Signage Manager communicates with media players through local area network (LAN). Please make sure below ports are opened & not blocked. Port TCP UDP Description 80 TCP Hypertext Transfer Protocol (HTTP), main communication port with legacy players (e.g. NMP-302w, NMP580-W, EP1031, EP1032, EP1042T, CDM4300R, CDM4900R,...

How to set up video wall in daisy chain?

Here’re major steps to set up video wall in portrait position for your reference. 1. Set up  monitor ID in OSD menu as 1~4 prior to mounting monitors.   2. Connect  IR sensor cable to monitor 1.   3. Connect  the PC to monitor 1 with DP cable firstly for easy setup & adjustment  afterwards.   4. Mounting  monitor 1/2/3/4 in portrait p...

How to upgrade the firmware on Stand type EPoster, EP5520/EP5520T, EP5540/EP5540T, EP5542/EP5542T?

1. Format the USB disk as FAT32. 2. Unzip the “MstarUpgrade_848.zip” and then copy the .bin file to the USB disk (FAT32) in the root directory. 3. In Android mode, press the Source menu button, then press INPUT 9 9 1 to open the Service Menu. 4. Select "Firmware Update" and press OK.  5. Select "Upgrade Main" and press OK. ...

How to check CDX series , videowall, model RS232 daisy chain working correctly

1. Is it correct of RS232 daisy chain cable ? 2. In OSD menu, General settings -> Eco mode please set to Normal. (If set to Low power standby, the unit can power OFF but can’t power ON) 3. The RS232 daisy chain cable is 2.4mm – 2.4mm

How can I add other widgets to the Signage manager software?

You can refer below steps to use other widgets.

ViewSonic CDE30 Series Power Save Modes: Which Mode Should I Use?

ViewSonic CDE30 Series power save modes: Which mode should i use? There are four Power Save modes to choose from and knowing which one to use depends on the application. For this scenario we will cover digital signage, information and monitoring systems and meeting rooms where always-on, wake up on active signal and fast boot time is a must...

What USB WiFi dongle/adapter will work with commercial displays, the CDM, CDE, EP series?

Model Name CDM series CDE10 series CDE20 series EP5540/T EP5542/T Supported WiFi Dongle Built-in WiFi module LB-WiFi-001 LB-WiFi-001 TL-WN725N TL-WN725N TL-WN725N TL-WN725N VSB050 VSB050 VB-WIFI-001 Note: 1. WPA stands for Wi-Fi Protected Access.  2. All WiFi modules and dongles only support W...